Trying a PWM audio application. I can't figure out why I'm getting a loud beep overlapping my sound
1
I want to play some short audio clips (they range from 50ms to 100ms) from my atmega168 microcontroller and output it to a cheap speaker.
I was following this tutorial but because I'm using a atmega168 and not a atmega2560, I had to modify my code as well as replaced the sound.
Like in the tutorial, I'm using a 8MHz internal oscillator (I set LFUSE = 0xE2 in the Makefile) and all the PWM settings are the same...which means
- Using a 16 Timer/Counter1 with 8-bit PWM resolution
- Set OC1A on compare match (and clear on bottom)
- No prescaling
As for the sound clip, I sampled it at 15.625 kHz and exported it to a 8-bit PCM wav file. I then get a hex dump via xxd -i which gives me the output c file. I didn't remove the header as I figured I can just skip it by just going to the 44th position of the output array as it is the data position.
The problem I'm having is that while I do get my (distorted and soft) sound, there is this loud beeping noise that is overlapping with my sound and I have no idea what is causing it.
Unfortunately I don't have access to an oscilloscope, so I can't really nail down if it is the way I sampled my sound, or if my sound is way too short or something that's beyond my current understanding.
Main.c
#include <inttypes.h>
#include <avr/io.h>
#include <avr/interrupt.h>
#include <util/delay.h>
#include <avr/pgmspace.h>
#include <avr/power.h>
#include <util/setbaud.h>
#include <avr/interrupt.h>
#include "switch.h"
#define WAV_DATA_POSITION 44
#define BASE_LEVEL 0xff
unsigned int count=WAV_DATA_POSITION;;
volatile uint16_t timerOverflowCount;
unsigned char sample_count =2;
// This interrupt service reads new data,
ISR(TIMER1_OVF_vect){
sample_count--;
if(sample_count ==0)
{
sample_count = 2;
if (count < switchResampled_len){
OCR1A= pgm_read_byte(&switch_raw[count]);
count++;
}
}
else{
OCR1A= BASE_LEVEL;
}
}
void pwm_init()
{
SREG |=0x80;
//select Fast PWM with 8-bit resolution,set OC1A on compare match and clear at bottom
TCCR1A|=(1<<COM1A1)|(1<<COM1A0)|(1<<WGM10);
//No prescaling therefore timer frequency = 8 MHz and PWM frequency = 31250 Hz
TCCR1B|=(1<<WGM12)|(1<<CS10);
TCNT1=0x00;
OCR1A=BASE_LEVEL;
//Enable the timer interrupt
TIMSK1 |= ( 1 <<TOIE1);
//Clear all interupt flags
TIFR1|=(1<<ICF1)|(1<<OCF1B)|(1<<OCF1A)|(1<<TOV1);
//Enable interrupts
sei();
}
int main(void)
{
//PB1 is OC1A. Use this for output
DDRB |= (1 << PB1);
pwm_init();
/* insert your hardware initialization here */
for(;;){
/* insert your main loop code here */
}
return 0; /* never reached */
}
Switch.h (Sound file)
const unsigned char switch_raw PROGMEM = {
0x52, 0x49, 0x46, 0x46, 0x0d, 0x04, 0x00, 0x00, 0x57, 0x41, 0x56, 0x45,
0x66, 0x6d, 0x74, 0x20, 0x10, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x00,
0x09, 0x3d, 0x00, 0x00, 0x09, 0x3d, 0x00, 0x00, 0x01, 0x00, 0x08, 0x00,
0x64, 0x61, 0x74, 0x61, 0x4b, 0x03, 0x00, 0x00, 0x80, 0x7f, 0x7f, 0x7e,
0x7f, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7f, 0x80, 0x7f, 0x7e, 0x7e,
0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7d, 0x7f, 0x81, 0x7e, 0x7e, 0x7f, 0x7f,
0x7e, 0x7e, 0x7f, 0x7f, 0x7f, 0x7d, 0x80, 0x81, 0x7e, 0x7b, 0x7e, 0x7f,
0x7f, 0x81, 0x7e, 0x7e, 0x7d, 0x80, 0x80, 0x7e, 0x7e, 0x7e, 0x7d, 0x7e,
0x80, 0x80, 0x7e, 0x7c, 0x7d, 0x7f, 0x81, 0x7f, 0x7e, 0x81, 0x7d, 0x7b,
0x80, 0x7f, 0x7f, 0x83, 0x7f, 0x7b, 0x7f, 0x80, 0x7f, 0x82, 0x7f, 0x7e,
0x80, 0x7e, 0x81, 0x7f, 0x7f, 0x81, 0x7d, 0x7e, 0x80, 0x7e, 0x80, 0x7e,
0x7f, 0x85, 0x80, 0x83, 0x7b, 0x77, 0x83, 0x81, 0x86, 0x7e, 0x7b, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x7f, 0x81, 0x82, 0x7f, 0x7e, 0x7e, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x80, 0x80, 0x81, 0x7e, 0x7e, 0x80, 0x83,
0x7f, 0x7d, 0x7b, 0x80, 0x80, 0x94, 0x79, 0x68, 0x87, 0x75, 0x98, 0x87,
0x6e, 0x7f, 0x8c, 0x81, 0x54, 0x7c, 0xc4, 0x8a, 0x46, 0x31, 0x72, 0xe2,
0xc1, 0x8a, 0x41, 0x2f, 0x71, 0xb3, 0xc8, 0x96, 0x51, 0x41, 0x67, 0x9c,
0xb1, 0x98, 0x74, 0x57, 0x5f, 0x76, 0x99, 0xa8, 0x96, 0x72, 0x5b, 0x64,
0x7e, 0x97, 0xa1, 0x8f, 0x6f, 0x56, 0x66, 0x89, 0xa0, 0x9d, 0x7e, 0x62,
0x5c, 0x78, 0x93, 0x9d, 0x90, 0x70, 0x58, 0x68, 0x88, 0x9c, 0x95, 0x7c,
0x66, 0x64, 0x7c, 0x90, 0x95, 0x82, 0x6f, 0x6b, 0x75, 0x86, 0x8e, 0x88,
0x79, 0x72, 0x75, 0x80, 0x88, 0x89, 0x81, 0x78, 0x74, 0x78, 0x84, 0x85,
0x84, 0x7d, 0x7b, 0x7c, 0x7b, 0x80, 0x85, 0x87, 0x81, 0x76, 0x74, 0x7e,
0x82, 0x89, 0x84, 0x7c, 0x77, 0x78, 0x84, 0x83, 0x84, 0x7c, 0x78, 0x7b,
0x83, 0x83, 0x80, 0x83, 0x80, 0x7d, 0x7a, 0x7e, 0x83, 0x87, 0x82, 0x79,
0x78, 0x7e, 0x87, 0x8b, 0x80, 0x76, 0x79, 0x7e, 0x87, 0x87, 0x80, 0x7a,
0x7a, 0x80, 0x82, 0x84, 0x81, 0x7f, 0x7e, 0x7d, 0x7a, 0x82, 0x88, 0x7f,
0x7a, 0x79, 0x7f, 0x85, 0x85, 0x7f, 0x7d, 0x7a, 0x7d, 0x83, 0x87, 0x7e,
0x78, 0x7e, 0x7d, 0x83, 0x7e, 0x81, 0x81, 0x80, 0x7f, 0x81, 0x81, 0x7c,
0x7e, 0x7a, 0x81, 0x82, 0x81, 0x84, 0x82, 0x79, 0x78, 0x84, 0x86, 0x7d,
0x7b, 0x7e, 0x7f, 0x7c, 0x7d, 0x7d, 0x82, 0x80, 0x80, 0x7e, 0x7d, 0x85,
0x84, 0x7b, 0x75, 0x7c, 0x7d, 0x84, 0x88, 0x84, 0x7b, 0x7b, 0x7d, 0x7c,
0x88, 0x88, 0x7b, 0x78, 0x78, 0x78, 0x88, 0x8d, 0x80, 0x78, 0x7f, 0x86,
0x86, 0x83, 0x7c, 0x71, 0x76, 0x84, 0x97, 0x93, 0x70, 0x6d, 0x68, 0x78,
0xc5, 0xb6, 0x5f, 0x37, 0x2a, 0x69, 0xc1, 0xc9, 0xa0, 0x7a, 0x52, 0x50,
0x71, 0x8a, 0x9d, 0xa0, 0x8b, 0x69, 0x67, 0x68, 0x79, 0x94, 0x96, 0x87,
0x7b, 0x81, 0x84, 0x7e, 0x7d, 0x7e, 0x75, 0x72, 0x89, 0x8e, 0x88, 0x86,
0x6d, 0x6d, 0x7a, 0x82, 0x8d, 0x8e, 0x78, 0x76, 0x7f, 0x7d, 0x7e, 0x82,
0x80, 0x7b, 0x7d, 0x7a, 0x7b, 0x86, 0x89, 0x80, 0x7b, 0x75, 0x77, 0x7f,
0x83, 0x84, 0x86, 0x81, 0x81, 0x7e, 0x73, 0x7c, 0x83, 0x7f, 0x85, 0x82,
0x7d, 0x83, 0x7d, 0x7d, 0x80, 0x7b, 0x7c, 0x86, 0x85, 0x7e, 0x7b, 0x74,
0x7d, 0x86, 0x85, 0x8b, 0x81, 0x76, 0x78, 0x78, 0x7e, 0x89, 0x83, 0x7e,
0x80, 0x78, 0x7f, 0x84, 0x81, 0x84, 0x7a, 0x77, 0x7f, 0x81, 0x84, 0x81,
0x78, 0x7a, 0x7e, 0x84, 0x8e, 0x81, 0x72, 0x75, 0x77, 0x83, 0x8b, 0x84,
0x84, 0x7b, 0x72, 0x7a, 0x83, 0x84, 0x85, 0x7e, 0x78, 0x7e, 0x7d, 0x7f,
0x82, 0x80, 0x7f, 0x7e, 0x7f, 0x81, 0x7e, 0x7b, 0x80, 0x85, 0x84, 0x82,
0x7d, 0x7a, 0x7d, 0x7f, 0x84, 0x84, 0x7f, 0x79, 0x7b, 0x82, 0x80, 0x80,
0x81, 0x80, 0x81, 0x81, 0x7f, 0x7e, 0x79, 0x79, 0x81, 0x86, 0x85, 0x82,
0x7d, 0x77, 0x7a, 0x7e, 0x86, 0x8b, 0x84, 0x7a, 0x7a, 0x7d, 0x7e, 0x83,
0x83, 0x80, 0x7e, 0x7c, 0x7c, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x80, 0x7e,
0x7f, 0x80, 0x7f, 0x7c, 0x80, 0x7d, 0x7e, 0x85, 0x81, 0x7c, 0x7d, 0x7b,
0x7c, 0x81, 0x80, 0x7d, 0x7f, 0x80, 0x7d, 0x82, 0x84, 0x7e, 0x7a, 0x7e,
0x7e, 0x7f, 0x82, 0x7d, 0x7e, 0x81, 0x7f, 0x7d, 0x7e, 0x81, 0x83, 0x83,
0x80, 0x79, 0x77, 0x7c, 0x83, 0x87, 0x86, 0x7f, 0x75, 0x79, 0x7e, 0x85,
0x86, 0x80, 0x7a, 0x78, 0x7c, 0x7f, 0x83, 0x81, 0x82, 0x7d, 0x7a, 0x7f,
0x81, 0x80, 0x80, 0x7c, 0x7b, 0x80, 0x7e, 0x80, 0x85, 0x84, 0x7d, 0x7b,
0x7a, 0x7f, 0x83, 0x82, 0x80, 0x7c, 0x7e, 0x7e, 0x80, 0x81, 0x7f, 0x7f,
0x7e, 0x7f, 0x82, 0x7f, 0x7c, 0x7b, 0x7b, 0x82, 0x84, 0x83, 0x7e, 0x7c,
0x7b, 0x7e, 0x83, 0x81, 0x7f, 0x7d, 0x7e, 0x7f, 0x83, 0x81, 0x7e, 0x7d,
0x7b, 0x7d, 0x80, 0x82, 0x81, 0x80, 0x7f, 0x7d, 0x7f, 0x80, 0x7f, 0x80,
0x81, 0x80, 0x7f, 0x7d, 0x7d, 0x7e, 0x81, 0x82, 0x80, 0x7d, 0x7f, 0x81,
0x80, 0x7f, 0x7d, 0x7c, 0x7e, 0x80, 0x80, 0x80, 0x80, 0x80, 0x7e, 0x7f,
0x7d, 0x7e, 0x80, 0x81, 0x80, 0x7f, 0x7e, 0x7c, 0x7f, 0x81, 0x80, 0x80,
0x80, 0x7f, 0x7e, 0x7e, 0x7f, 0x7f, 0x80, 0x80, 0x80, 0x81, 0x80, 0x7d,
0x7c, 0x7f, 0x80, 0x83, 0x81, 0x7c, 0x7b, 0x7c, 0x7f, 0x82, 0x82, 0x7f,
0x7d, 0x7c, 0x7e, 0x80, 0x81, 0x81, 0x7f, 0x7f, 0x7d, 0x7d, 0x80, 0x82,
0x7f, 0x7e, 0x7d, 0x7d, 0x80, 0x83, 0x82, 0x7f, 0x7f, 0x7a, 0x7d, 0x80,
0x81, 0x81, 0x80, 0x7e, 0x7f, 0x80, 0x7e, 0x7e, 0x7f, 0x80, 0x7f, 0x80,
0x7f, 0x7e, 0x7d, 0x7f, 0x7e, 0x80, 0x81, 0x81, 0x80, 0x80, 0x7e, 0x7e,
0x7e, 0x7d, 0x80, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7e, 0x7c, 0x7f, 0x82,
0x7f, 0x80, 0x7f, 0x7d, 0x7d, 0x7f, 0x7f, 0x80, 0x80, 0x7f, 0x7e, 0x7f,
0x7f, 0x7f, 0x80, 0x7e, 0x7f, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7d, 0x7d,
0x81, 0x82, 0x80, 0x7e, 0x7d, 0x7e, 0x80, 0x81, 0x7f, 0x80, 0x80, 0x7f,
0x7f, 0x7d, 0x7f, 0x81, 0x80, 0x7f, 0x80, 0x7f, 0x7e, 0x7d, 0x7e, 0x4c,
0x49, 0x53, 0x54, 0x48, 0x00, 0x00, 0x00, 0x49, 0x4e, 0x46, 0x4f, 0x49,
0x43, 0x52, 0x44, 0x12, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31, 0x36, 0x2d,
0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32, 0x37, 0x00,
0x00, 0x49, 0x53, 0x46, 0x54, 0x22, 0x00, 0x00, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x20, 0x28,
0x6c, 0x69, 0x62, 0x73, 0x6e, 0x64, 0x66, 0x69, 0x6c, 0x65, 0x2d, 0x31,
0x2e, 0x30, 0x2e, 0x32, 0x34, 0x29, 0x00, 0x69, 0x64, 0x33, 0x20, 0x46,
0x00, 0x00, 0x00, 0x49, 0x44, 0x33, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00,
0x3c, 0x54, 0x58, 0x58, 0x58, 0x00, 0x00, 0x00, 0x17, 0x00, 0x00, 0x00,
0x53, 0x6f, 0x66, 0x74, 0x77, 0x61, 0x72, 0x65, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x54, 0x44,
0x52, 0x43, 0x00, 0x00, 0x00, 0x11, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31,
0x36, 0x2d, 0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32,
0x37
};
const long switchResampled_len = 1045;
audio pwm atmega
asked 4 hours ago
cheunste
584
add a comment |
1
I want to play some short audio clips (they range from 50ms to 100ms) from my atmega168 microcontroller and output it to a cheap speaker.
I was following this tutorial but because I'm using a atmega168 and not a atmega2560, I had to modify my code as well as replaced the sound.
Like in the tutorial, I'm using a 8MHz internal oscillator (I set LFUSE = 0xE2 in the Makefile) and all the PWM settings are the same...which means
- Using a 16 Timer/Counter1 with 8-bit PWM resolution
- Set OC1A on compare match (and clear on bottom)
- No prescaling
As for the sound clip, I sampled it at 15.625 kHz and exported it to a 8-bit PCM wav file. I then get a hex dump via xxd -i which gives me the output c file. I didn't remove the header as I figured I can just skip it by just going to the 44th position of the output array as it is the data position.
The problem I'm having is that while I do get my (distorted and soft) sound, there is this loud beeping noise that is overlapping with my sound and I have no idea what is causing it.
Unfortunately I don't have access to an oscilloscope, so I can't really nail down if it is the way I sampled my sound, or if my sound is way too short or something that's beyond my current understanding.
Main.c
#include <inttypes.h>
#include <avr/io.h>
#include <avr/interrupt.h>
#include <util/delay.h>
#include <avr/pgmspace.h>
#include <avr/power.h>
#include <util/setbaud.h>
#include <avr/interrupt.h>
#include "switch.h"
#define WAV_DATA_POSITION 44
#define BASE_LEVEL 0xff
unsigned int count=WAV_DATA_POSITION;;
volatile uint16_t timerOverflowCount;
unsigned char sample_count =2;
// This interrupt service reads new data,
ISR(TIMER1_OVF_vect){
sample_count--;
if(sample_count ==0)
{
sample_count = 2;
if (count < switchResampled_len){
OCR1A= pgm_read_byte(&switch_raw[count]);
count++;
}
}
else{
OCR1A= BASE_LEVEL;
}
}
void pwm_init()
{
SREG |=0x80;
//select Fast PWM with 8-bit resolution,set OC1A on compare match and clear at bottom
TCCR1A|=(1<<COM1A1)|(1<<COM1A0)|(1<<WGM10);
//No prescaling therefore timer frequency = 8 MHz and PWM frequency = 31250 Hz
TCCR1B|=(1<<WGM12)|(1<<CS10);
TCNT1=0x00;
OCR1A=BASE_LEVEL;
//Enable the timer interrupt
TIMSK1 |= ( 1 <<TOIE1);
//Clear all interupt flags
TIFR1|=(1<<ICF1)|(1<<OCF1B)|(1<<OCF1A)|(1<<TOV1);
//Enable interrupts
sei();
}
int main(void)
{
//PB1 is OC1A. Use this for output
DDRB |= (1 << PB1);
pwm_init();
/* insert your hardware initialization here */
for(;;){
/* insert your main loop code here */
}
return 0; /* never reached */
}
Switch.h (Sound file)
const unsigned char switch_raw PROGMEM = {
0x52, 0x49, 0x46, 0x46, 0x0d, 0x04, 0x00, 0x00, 0x57, 0x41, 0x56, 0x45,
0x66, 0x6d, 0x74, 0x20, 0x10, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x00,
0x09, 0x3d, 0x00, 0x00, 0x09, 0x3d, 0x00, 0x00, 0x01, 0x00, 0x08, 0x00,
0x64, 0x61, 0x74, 0x61, 0x4b, 0x03, 0x00, 0x00, 0x80, 0x7f, 0x7f, 0x7e,
0x7f, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7f, 0x80, 0x7f, 0x7e, 0x7e,
0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7d, 0x7f, 0x81, 0x7e, 0x7e, 0x7f, 0x7f,
0x7e, 0x7e, 0x7f, 0x7f, 0x7f, 0x7d, 0x80, 0x81, 0x7e, 0x7b, 0x7e, 0x7f,
0x7f, 0x81, 0x7e, 0x7e, 0x7d, 0x80, 0x80, 0x7e, 0x7e, 0x7e, 0x7d, 0x7e,
0x80, 0x80, 0x7e, 0x7c, 0x7d, 0x7f, 0x81, 0x7f, 0x7e, 0x81, 0x7d, 0x7b,
0x80, 0x7f, 0x7f, 0x83, 0x7f, 0x7b, 0x7f, 0x80, 0x7f, 0x82, 0x7f, 0x7e,
0x80, 0x7e, 0x81, 0x7f, 0x7f, 0x81, 0x7d, 0x7e, 0x80, 0x7e, 0x80, 0x7e,
0x7f, 0x85, 0x80, 0x83, 0x7b, 0x77, 0x83, 0x81, 0x86, 0x7e, 0x7b, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x7f, 0x81, 0x82, 0x7f, 0x7e, 0x7e, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x80, 0x80, 0x81, 0x7e, 0x7e, 0x80, 0x83,
0x7f, 0x7d, 0x7b, 0x80, 0x80, 0x94, 0x79, 0x68, 0x87, 0x75, 0x98, 0x87,
0x6e, 0x7f, 0x8c, 0x81, 0x54, 0x7c, 0xc4, 0x8a, 0x46, 0x31, 0x72, 0xe2,
0xc1, 0x8a, 0x41, 0x2f, 0x71, 0xb3, 0xc8, 0x96, 0x51, 0x41, 0x67, 0x9c,
0xb1, 0x98, 0x74, 0x57, 0x5f, 0x76, 0x99, 0xa8, 0x96, 0x72, 0x5b, 0x64,
0x7e, 0x97, 0xa1, 0x8f, 0x6f, 0x56, 0x66, 0x89, 0xa0, 0x9d, 0x7e, 0x62,
0x5c, 0x78, 0x93, 0x9d, 0x90, 0x70, 0x58, 0x68, 0x88, 0x9c, 0x95, 0x7c,
0x66, 0x64, 0x7c, 0x90, 0x95, 0x82, 0x6f, 0x6b, 0x75, 0x86, 0x8e, 0x88,
0x79, 0x72, 0x75, 0x80, 0x88, 0x89, 0x81, 0x78, 0x74, 0x78, 0x84, 0x85,
0x84, 0x7d, 0x7b, 0x7c, 0x7b, 0x80, 0x85, 0x87, 0x81, 0x76, 0x74, 0x7e,
0x82, 0x89, 0x84, 0x7c, 0x77, 0x78, 0x84, 0x83, 0x84, 0x7c, 0x78, 0x7b,
0x83, 0x83, 0x80, 0x83, 0x80, 0x7d, 0x7a, 0x7e, 0x83, 0x87, 0x82, 0x79,
0x78, 0x7e, 0x87, 0x8b, 0x80, 0x76, 0x79, 0x7e, 0x87, 0x87, 0x80, 0x7a,
0x7a, 0x80, 0x82, 0x84, 0x81, 0x7f, 0x7e, 0x7d, 0x7a, 0x82, 0x88, 0x7f,
0x7a, 0x79, 0x7f, 0x85, 0x85, 0x7f, 0x7d, 0x7a, 0x7d, 0x83, 0x87, 0x7e,
0x78, 0x7e, 0x7d, 0x83, 0x7e, 0x81, 0x81, 0x80, 0x7f, 0x81, 0x81, 0x7c,
0x7e, 0x7a, 0x81, 0x82, 0x81, 0x84, 0x82, 0x79, 0x78, 0x84, 0x86, 0x7d,
0x7b, 0x7e, 0x7f, 0x7c, 0x7d, 0x7d, 0x82, 0x80, 0x80, 0x7e, 0x7d, 0x85,
0x84, 0x7b, 0x75, 0x7c, 0x7d, 0x84, 0x88, 0x84, 0x7b, 0x7b, 0x7d, 0x7c,
0x88, 0x88, 0x7b, 0x78, 0x78, 0x78, 0x88, 0x8d, 0x80, 0x78, 0x7f, 0x86,
0x86, 0x83, 0x7c, 0x71, 0x76, 0x84, 0x97, 0x93, 0x70, 0x6d, 0x68, 0x78,
0xc5, 0xb6, 0x5f, 0x37, 0x2a, 0x69, 0xc1, 0xc9, 0xa0, 0x7a, 0x52, 0x50,
0x71, 0x8a, 0x9d, 0xa0, 0x8b, 0x69, 0x67, 0x68, 0x79, 0x94, 0x96, 0x87,
0x7b, 0x81, 0x84, 0x7e, 0x7d, 0x7e, 0x75, 0x72, 0x89, 0x8e, 0x88, 0x86,
0x6d, 0x6d, 0x7a, 0x82, 0x8d, 0x8e, 0x78, 0x76, 0x7f, 0x7d, 0x7e, 0x82,
0x80, 0x7b, 0x7d, 0x7a, 0x7b, 0x86, 0x89, 0x80, 0x7b, 0x75, 0x77, 0x7f,
0x83, 0x84, 0x86, 0x81, 0x81, 0x7e, 0x73, 0x7c, 0x83, 0x7f, 0x85, 0x82,
0x7d, 0x83, 0x7d, 0x7d, 0x80, 0x7b, 0x7c, 0x86, 0x85, 0x7e, 0x7b, 0x74,
0x7d, 0x86, 0x85, 0x8b, 0x81, 0x76, 0x78, 0x78, 0x7e, 0x89, 0x83, 0x7e,
0x80, 0x78, 0x7f, 0x84, 0x81, 0x84, 0x7a, 0x77, 0x7f, 0x81, 0x84, 0x81,
0x78, 0x7a, 0x7e, 0x84, 0x8e, 0x81, 0x72, 0x75, 0x77, 0x83, 0x8b, 0x84,
0x84, 0x7b, 0x72, 0x7a, 0x83, 0x84, 0x85, 0x7e, 0x78, 0x7e, 0x7d, 0x7f,
0x82, 0x80, 0x7f, 0x7e, 0x7f, 0x81, 0x7e, 0x7b, 0x80, 0x85, 0x84, 0x82,
0x7d, 0x7a, 0x7d, 0x7f, 0x84, 0x84, 0x7f, 0x79, 0x7b, 0x82, 0x80, 0x80,
0x81, 0x80, 0x81, 0x81, 0x7f, 0x7e, 0x79, 0x79, 0x81, 0x86, 0x85, 0x82,
0x7d, 0x77, 0x7a, 0x7e, 0x86, 0x8b, 0x84, 0x7a, 0x7a, 0x7d, 0x7e, 0x83,
0x83, 0x80, 0x7e, 0x7c, 0x7c, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x80, 0x7e,
0x7f, 0x80, 0x7f, 0x7c, 0x80, 0x7d, 0x7e, 0x85, 0x81, 0x7c, 0x7d, 0x7b,
0x7c, 0x81, 0x80, 0x7d, 0x7f, 0x80, 0x7d, 0x82, 0x84, 0x7e, 0x7a, 0x7e,
0x7e, 0x7f, 0x82, 0x7d, 0x7e, 0x81, 0x7f, 0x7d, 0x7e, 0x81, 0x83, 0x83,
0x80, 0x79, 0x77, 0x7c, 0x83, 0x87, 0x86, 0x7f, 0x75, 0x79, 0x7e, 0x85,
0x86, 0x80, 0x7a, 0x78, 0x7c, 0x7f, 0x83, 0x81, 0x82, 0x7d, 0x7a, 0x7f,
0x81, 0x80, 0x80, 0x7c, 0x7b, 0x80, 0x7e, 0x80, 0x85, 0x84, 0x7d, 0x7b,
0x7a, 0x7f, 0x83, 0x82, 0x80, 0x7c, 0x7e, 0x7e, 0x80, 0x81, 0x7f, 0x7f,
0x7e, 0x7f, 0x82, 0x7f, 0x7c, 0x7b, 0x7b, 0x82, 0x84, 0x83, 0x7e, 0x7c,
0x7b, 0x7e, 0x83, 0x81, 0x7f, 0x7d, 0x7e, 0x7f, 0x83, 0x81, 0x7e, 0x7d,
0x7b, 0x7d, 0x80, 0x82, 0x81, 0x80, 0x7f, 0x7d, 0x7f, 0x80, 0x7f, 0x80,
0x81, 0x80, 0x7f, 0x7d, 0x7d, 0x7e, 0x81, 0x82, 0x80, 0x7d, 0x7f, 0x81,
0x80, 0x7f, 0x7d, 0x7c, 0x7e, 0x80, 0x80, 0x80, 0x80, 0x80, 0x7e, 0x7f,
0x7d, 0x7e, 0x80, 0x81, 0x80, 0x7f, 0x7e, 0x7c, 0x7f, 0x81, 0x80, 0x80,
0x80, 0x7f, 0x7e, 0x7e, 0x7f, 0x7f, 0x80, 0x80, 0x80, 0x81, 0x80, 0x7d,
0x7c, 0x7f, 0x80, 0x83, 0x81, 0x7c, 0x7b, 0x7c, 0x7f, 0x82, 0x82, 0x7f,
0x7d, 0x7c, 0x7e, 0x80, 0x81, 0x81, 0x7f, 0x7f, 0x7d, 0x7d, 0x80, 0x82,
0x7f, 0x7e, 0x7d, 0x7d, 0x80, 0x83, 0x82, 0x7f, 0x7f, 0x7a, 0x7d, 0x80,
0x81, 0x81, 0x80, 0x7e, 0x7f, 0x80, 0x7e, 0x7e, 0x7f, 0x80, 0x7f, 0x80,
0x7f, 0x7e, 0x7d, 0x7f, 0x7e, 0x80, 0x81, 0x81, 0x80, 0x80, 0x7e, 0x7e,
0x7e, 0x7d, 0x80, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7e, 0x7c, 0x7f, 0x82,
0x7f, 0x80, 0x7f, 0x7d, 0x7d, 0x7f, 0x7f, 0x80, 0x80, 0x7f, 0x7e, 0x7f,
0x7f, 0x7f, 0x80, 0x7e, 0x7f, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7d, 0x7d,
0x81, 0x82, 0x80, 0x7e, 0x7d, 0x7e, 0x80, 0x81, 0x7f, 0x80, 0x80, 0x7f,
0x7f, 0x7d, 0x7f, 0x81, 0x80, 0x7f, 0x80, 0x7f, 0x7e, 0x7d, 0x7e, 0x4c,
0x49, 0x53, 0x54, 0x48, 0x00, 0x00, 0x00, 0x49, 0x4e, 0x46, 0x4f, 0x49,
0x43, 0x52, 0x44, 0x12, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31, 0x36, 0x2d,
0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32, 0x37, 0x00,
0x00, 0x49, 0x53, 0x46, 0x54, 0x22, 0x00, 0x00, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x20, 0x28,
0x6c, 0x69, 0x62, 0x73, 0x6e, 0x64, 0x66, 0x69, 0x6c, 0x65, 0x2d, 0x31,
0x2e, 0x30, 0x2e, 0x32, 0x34, 0x29, 0x00, 0x69, 0x64, 0x33, 0x20, 0x46,
0x00, 0x00, 0x00, 0x49, 0x44, 0x33, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00,
0x3c, 0x54, 0x58, 0x58, 0x58, 0x00, 0x00, 0x00, 0x17, 0x00, 0x00, 0x00,
0x53, 0x6f, 0x66, 0x74, 0x77, 0x61, 0x72, 0x65, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x54, 0x44,
0x52, 0x43, 0x00, 0x00, 0x00, 0x11, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31,
0x36, 0x2d, 0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32,
0x37
};
const long switchResampled_len = 1045;
audio pwm atmega
asked 4 hours ago
cheunste
584
That is likely the fundamental PWM rate, wherein you are modifying the DUTY CYCLE but not the repetition rate.
– analogsystemsrf
4 hours ago
1045 samples at 15.625kHz is only 67mSec worth of data. How are you hearing anything in only 67mSec?
– brhans
4 hours ago
add a comment |
1
1
1
I want to play some short audio clips (they range from 50ms to 100ms) from my atmega168 microcontroller and output it to a cheap speaker.
I was following this tutorial but because I'm using a atmega168 and not a atmega2560, I had to modify my code as well as replaced the sound.
Like in the tutorial, I'm using a 8MHz internal oscillator (I set LFUSE = 0xE2 in the Makefile) and all the PWM settings are the same...which means
- Using a 16 Timer/Counter1 with 8-bit PWM resolution
- Set OC1A on compare match (and clear on bottom)
- No prescaling
As for the sound clip, I sampled it at 15.625 kHz and exported it to a 8-bit PCM wav file. I then get a hex dump via xxd -i which gives me the output c file. I didn't remove the header as I figured I can just skip it by just going to the 44th position of the output array as it is the data position.
The problem I'm having is that while I do get my (distorted and soft) sound, there is this loud beeping noise that is overlapping with my sound and I have no idea what is causing it.
Unfortunately I don't have access to an oscilloscope, so I can't really nail down if it is the way I sampled my sound, or if my sound is way too short or something that's beyond my current understanding.
Main.c
#include <inttypes.h>
#include <avr/io.h>
#include <avr/interrupt.h>
#include <util/delay.h>
#include <avr/pgmspace.h>
#include <avr/power.h>
#include <util/setbaud.h>
#include <avr/interrupt.h>
#include "switch.h"
#define WAV_DATA_POSITION 44
#define BASE_LEVEL 0xff
unsigned int count=WAV_DATA_POSITION;;
volatile uint16_t timerOverflowCount;
unsigned char sample_count =2;
// This interrupt service reads new data,
ISR(TIMER1_OVF_vect){
sample_count--;
if(sample_count ==0)
{
sample_count = 2;
if (count < switchResampled_len){
OCR1A= pgm_read_byte(&switch_raw[count]);
count++;
}
}
else{
OCR1A= BASE_LEVEL;
}
}
void pwm_init()
{
SREG |=0x80;
//select Fast PWM with 8-bit resolution,set OC1A on compare match and clear at bottom
TCCR1A|=(1<<COM1A1)|(1<<COM1A0)|(1<<WGM10);
//No prescaling therefore timer frequency = 8 MHz and PWM frequency = 31250 Hz
TCCR1B|=(1<<WGM12)|(1<<CS10);
TCNT1=0x00;
OCR1A=BASE_LEVEL;
//Enable the timer interrupt
TIMSK1 |= ( 1 <<TOIE1);
//Clear all interupt flags
TIFR1|=(1<<ICF1)|(1<<OCF1B)|(1<<OCF1A)|(1<<TOV1);
//Enable interrupts
sei();
}
int main(void)
{
//PB1 is OC1A. Use this for output
DDRB |= (1 << PB1);
pwm_init();
/* insert your hardware initialization here */
for(;;){
/* insert your main loop code here */
}
return 0; /* never reached */
}
Switch.h (Sound file)
const unsigned char switch_raw PROGMEM = {
0x52, 0x49, 0x46, 0x46, 0x0d, 0x04, 0x00, 0x00, 0x57, 0x41, 0x56, 0x45,
0x66, 0x6d, 0x74, 0x20, 0x10, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x00,
0x09, 0x3d, 0x00, 0x00, 0x09, 0x3d, 0x00, 0x00, 0x01, 0x00, 0x08, 0x00,
0x64, 0x61, 0x74, 0x61, 0x4b, 0x03, 0x00, 0x00, 0x80, 0x7f, 0x7f, 0x7e,
0x7f, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7f, 0x80, 0x7f, 0x7e, 0x7e,
0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7d, 0x7f, 0x81, 0x7e, 0x7e, 0x7f, 0x7f,
0x7e, 0x7e, 0x7f, 0x7f, 0x7f, 0x7d, 0x80, 0x81, 0x7e, 0x7b, 0x7e, 0x7f,
0x7f, 0x81, 0x7e, 0x7e, 0x7d, 0x80, 0x80, 0x7e, 0x7e, 0x7e, 0x7d, 0x7e,
0x80, 0x80, 0x7e, 0x7c, 0x7d, 0x7f, 0x81, 0x7f, 0x7e, 0x81, 0x7d, 0x7b,
0x80, 0x7f, 0x7f, 0x83, 0x7f, 0x7b, 0x7f, 0x80, 0x7f, 0x82, 0x7f, 0x7e,
0x80, 0x7e, 0x81, 0x7f, 0x7f, 0x81, 0x7d, 0x7e, 0x80, 0x7e, 0x80, 0x7e,
0x7f, 0x85, 0x80, 0x83, 0x7b, 0x77, 0x83, 0x81, 0x86, 0x7e, 0x7b, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x7f, 0x81, 0x82, 0x7f, 0x7e, 0x7e, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x80, 0x80, 0x81, 0x7e, 0x7e, 0x80, 0x83,
0x7f, 0x7d, 0x7b, 0x80, 0x80, 0x94, 0x79, 0x68, 0x87, 0x75, 0x98, 0x87,
0x6e, 0x7f, 0x8c, 0x81, 0x54, 0x7c, 0xc4, 0x8a, 0x46, 0x31, 0x72, 0xe2,
0xc1, 0x8a, 0x41, 0x2f, 0x71, 0xb3, 0xc8, 0x96, 0x51, 0x41, 0x67, 0x9c,
0xb1, 0x98, 0x74, 0x57, 0x5f, 0x76, 0x99, 0xa8, 0x96, 0x72, 0x5b, 0x64,
0x7e, 0x97, 0xa1, 0x8f, 0x6f, 0x56, 0x66, 0x89, 0xa0, 0x9d, 0x7e, 0x62,
0x5c, 0x78, 0x93, 0x9d, 0x90, 0x70, 0x58, 0x68, 0x88, 0x9c, 0x95, 0x7c,
0x66, 0x64, 0x7c, 0x90, 0x95, 0x82, 0x6f, 0x6b, 0x75, 0x86, 0x8e, 0x88,
0x79, 0x72, 0x75, 0x80, 0x88, 0x89, 0x81, 0x78, 0x74, 0x78, 0x84, 0x85,
0x84, 0x7d, 0x7b, 0x7c, 0x7b, 0x80, 0x85, 0x87, 0x81, 0x76, 0x74, 0x7e,
0x82, 0x89, 0x84, 0x7c, 0x77, 0x78, 0x84, 0x83, 0x84, 0x7c, 0x78, 0x7b,
0x83, 0x83, 0x80, 0x83, 0x80, 0x7d, 0x7a, 0x7e, 0x83, 0x87, 0x82, 0x79,
0x78, 0x7e, 0x87, 0x8b, 0x80, 0x76, 0x79, 0x7e, 0x87, 0x87, 0x80, 0x7a,
0x7a, 0x80, 0x82, 0x84, 0x81, 0x7f, 0x7e, 0x7d, 0x7a, 0x82, 0x88, 0x7f,
0x7a, 0x79, 0x7f, 0x85, 0x85, 0x7f, 0x7d, 0x7a, 0x7d, 0x83, 0x87, 0x7e,
0x78, 0x7e, 0x7d, 0x83, 0x7e, 0x81, 0x81, 0x80, 0x7f, 0x81, 0x81, 0x7c,
0x7e, 0x7a, 0x81, 0x82, 0x81, 0x84, 0x82, 0x79, 0x78, 0x84, 0x86, 0x7d,
0x7b, 0x7e, 0x7f, 0x7c, 0x7d, 0x7d, 0x82, 0x80, 0x80, 0x7e, 0x7d, 0x85,
0x84, 0x7b, 0x75, 0x7c, 0x7d, 0x84, 0x88, 0x84, 0x7b, 0x7b, 0x7d, 0x7c,
0x88, 0x88, 0x7b, 0x78, 0x78, 0x78, 0x88, 0x8d, 0x80, 0x78, 0x7f, 0x86,
0x86, 0x83, 0x7c, 0x71, 0x76, 0x84, 0x97, 0x93, 0x70, 0x6d, 0x68, 0x78,
0xc5, 0xb6, 0x5f, 0x37, 0x2a, 0x69, 0xc1, 0xc9, 0xa0, 0x7a, 0x52, 0x50,
0x71, 0x8a, 0x9d, 0xa0, 0x8b, 0x69, 0x67, 0x68, 0x79, 0x94, 0x96, 0x87,
0x7b, 0x81, 0x84, 0x7e, 0x7d, 0x7e, 0x75, 0x72, 0x89, 0x8e, 0x88, 0x86,
0x6d, 0x6d, 0x7a, 0x82, 0x8d, 0x8e, 0x78, 0x76, 0x7f, 0x7d, 0x7e, 0x82,
0x80, 0x7b, 0x7d, 0x7a, 0x7b, 0x86, 0x89, 0x80, 0x7b, 0x75, 0x77, 0x7f,
0x83, 0x84, 0x86, 0x81, 0x81, 0x7e, 0x73, 0x7c, 0x83, 0x7f, 0x85, 0x82,
0x7d, 0x83, 0x7d, 0x7d, 0x80, 0x7b, 0x7c, 0x86, 0x85, 0x7e, 0x7b, 0x74,
0x7d, 0x86, 0x85, 0x8b, 0x81, 0x76, 0x78, 0x78, 0x7e, 0x89, 0x83, 0x7e,
0x80, 0x78, 0x7f, 0x84, 0x81, 0x84, 0x7a, 0x77, 0x7f, 0x81, 0x84, 0x81,
0x78, 0x7a, 0x7e, 0x84, 0x8e, 0x81, 0x72, 0x75, 0x77, 0x83, 0x8b, 0x84,
0x84, 0x7b, 0x72, 0x7a, 0x83, 0x84, 0x85, 0x7e, 0x78, 0x7e, 0x7d, 0x7f,
0x82, 0x80, 0x7f, 0x7e, 0x7f, 0x81, 0x7e, 0x7b, 0x80, 0x85, 0x84, 0x82,
0x7d, 0x7a, 0x7d, 0x7f, 0x84, 0x84, 0x7f, 0x79, 0x7b, 0x82, 0x80, 0x80,
0x81, 0x80, 0x81, 0x81, 0x7f, 0x7e, 0x79, 0x79, 0x81, 0x86, 0x85, 0x82,
0x7d, 0x77, 0x7a, 0x7e, 0x86, 0x8b, 0x84, 0x7a, 0x7a, 0x7d, 0x7e, 0x83,
0x83, 0x80, 0x7e, 0x7c, 0x7c, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x80, 0x7e,
0x7f, 0x80, 0x7f, 0x7c, 0x80, 0x7d, 0x7e, 0x85, 0x81, 0x7c, 0x7d, 0x7b,
0x7c, 0x81, 0x80, 0x7d, 0x7f, 0x80, 0x7d, 0x82, 0x84, 0x7e, 0x7a, 0x7e,
0x7e, 0x7f, 0x82, 0x7d, 0x7e, 0x81, 0x7f, 0x7d, 0x7e, 0x81, 0x83, 0x83,
0x80, 0x79, 0x77, 0x7c, 0x83, 0x87, 0x86, 0x7f, 0x75, 0x79, 0x7e, 0x85,
0x86, 0x80, 0x7a, 0x78, 0x7c, 0x7f, 0x83, 0x81, 0x82, 0x7d, 0x7a, 0x7f,
0x81, 0x80, 0x80, 0x7c, 0x7b, 0x80, 0x7e, 0x80, 0x85, 0x84, 0x7d, 0x7b,
0x7a, 0x7f, 0x83, 0x82, 0x80, 0x7c, 0x7e, 0x7e, 0x80, 0x81, 0x7f, 0x7f,
0x7e, 0x7f, 0x82, 0x7f, 0x7c, 0x7b, 0x7b, 0x82, 0x84, 0x83, 0x7e, 0x7c,
0x7b, 0x7e, 0x83, 0x81, 0x7f, 0x7d, 0x7e, 0x7f, 0x83, 0x81, 0x7e, 0x7d,
0x7b, 0x7d, 0x80, 0x82, 0x81, 0x80, 0x7f, 0x7d, 0x7f, 0x80, 0x7f, 0x80,
0x81, 0x80, 0x7f, 0x7d, 0x7d, 0x7e, 0x81, 0x82, 0x80, 0x7d, 0x7f, 0x81,
0x80, 0x7f, 0x7d, 0x7c, 0x7e, 0x80, 0x80, 0x80, 0x80, 0x80, 0x7e, 0x7f,
0x7d, 0x7e, 0x80, 0x81, 0x80, 0x7f, 0x7e, 0x7c, 0x7f, 0x81, 0x80, 0x80,
0x80, 0x7f, 0x7e, 0x7e, 0x7f, 0x7f, 0x80, 0x80, 0x80, 0x81, 0x80, 0x7d,
0x7c, 0x7f, 0x80, 0x83, 0x81, 0x7c, 0x7b, 0x7c, 0x7f, 0x82, 0x82, 0x7f,
0x7d, 0x7c, 0x7e, 0x80, 0x81, 0x81, 0x7f, 0x7f, 0x7d, 0x7d, 0x80, 0x82,
0x7f, 0x7e, 0x7d, 0x7d, 0x80, 0x83, 0x82, 0x7f, 0x7f, 0x7a, 0x7d, 0x80,
0x81, 0x81, 0x80, 0x7e, 0x7f, 0x80, 0x7e, 0x7e, 0x7f, 0x80, 0x7f, 0x80,
0x7f, 0x7e, 0x7d, 0x7f, 0x7e, 0x80, 0x81, 0x81, 0x80, 0x80, 0x7e, 0x7e,
0x7e, 0x7d, 0x80, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7e, 0x7c, 0x7f, 0x82,
0x7f, 0x80, 0x7f, 0x7d, 0x7d, 0x7f, 0x7f, 0x80, 0x80, 0x7f, 0x7e, 0x7f,
0x7f, 0x7f, 0x80, 0x7e, 0x7f, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7d, 0x7d,
0x81, 0x82, 0x80, 0x7e, 0x7d, 0x7e, 0x80, 0x81, 0x7f, 0x80, 0x80, 0x7f,
0x7f, 0x7d, 0x7f, 0x81, 0x80, 0x7f, 0x80, 0x7f, 0x7e, 0x7d, 0x7e, 0x4c,
0x49, 0x53, 0x54, 0x48, 0x00, 0x00, 0x00, 0x49, 0x4e, 0x46, 0x4f, 0x49,
0x43, 0x52, 0x44, 0x12, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31, 0x36, 0x2d,
0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32, 0x37, 0x00,
0x00, 0x49, 0x53, 0x46, 0x54, 0x22, 0x00, 0x00, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x20, 0x28,
0x6c, 0x69, 0x62, 0x73, 0x6e, 0x64, 0x66, 0x69, 0x6c, 0x65, 0x2d, 0x31,
0x2e, 0x30, 0x2e, 0x32, 0x34, 0x29, 0x00, 0x69, 0x64, 0x33, 0x20, 0x46,
0x00, 0x00, 0x00, 0x49, 0x44, 0x33, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00,
0x3c, 0x54, 0x58, 0x58, 0x58, 0x00, 0x00, 0x00, 0x17, 0x00, 0x00, 0x00,
0x53, 0x6f, 0x66, 0x74, 0x77, 0x61, 0x72, 0x65, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x54, 0x44,
0x52, 0x43, 0x00, 0x00, 0x00, 0x11, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31,
0x36, 0x2d, 0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32,
0x37
};
const long switchResampled_len = 1045;
audio pwm atmega
asked 4 hours ago
cheunste
584
I want to play some short audio clips (they range from 50ms to 100ms) from my atmega168 microcontroller and output it to a cheap speaker.
I was following this tutorial but because I'm using a atmega168 and not a atmega2560, I had to modify my code as well as replaced the sound.
Like in the tutorial, I'm using a 8MHz internal oscillator (I set LFUSE = 0xE2 in the Makefile) and all the PWM settings are the same...which means
- Using a 16 Timer/Counter1 with 8-bit PWM resolution
- Set OC1A on compare match (and clear on bottom)
- No prescaling
As for the sound clip, I sampled it at 15.625 kHz and exported it to a 8-bit PCM wav file. I then get a hex dump via xxd -i which gives me the output c file. I didn't remove the header as I figured I can just skip it by just going to the 44th position of the output array as it is the data position.
The problem I'm having is that while I do get my (distorted and soft) sound, there is this loud beeping noise that is overlapping with my sound and I have no idea what is causing it.
Unfortunately I don't have access to an oscilloscope, so I can't really nail down if it is the way I sampled my sound, or if my sound is way too short or something that's beyond my current understanding.
Main.c
#include <inttypes.h>
#include <avr/io.h>
#include <avr/interrupt.h>
#include <util/delay.h>
#include <avr/pgmspace.h>
#include <avr/power.h>
#include <util/setbaud.h>
#include <avr/interrupt.h>
#include "switch.h"
#define WAV_DATA_POSITION 44
#define BASE_LEVEL 0xff
unsigned int count=WAV_DATA_POSITION;;
volatile uint16_t timerOverflowCount;
unsigned char sample_count =2;
// This interrupt service reads new data,
ISR(TIMER1_OVF_vect){
sample_count--;
if(sample_count ==0)
{
sample_count = 2;
if (count < switchResampled_len){
OCR1A= pgm_read_byte(&switch_raw[count]);
count++;
}
}
else{
OCR1A= BASE_LEVEL;
}
}
void pwm_init()
{
SREG |=0x80;
//select Fast PWM with 8-bit resolution,set OC1A on compare match and clear at bottom
TCCR1A|=(1<<COM1A1)|(1<<COM1A0)|(1<<WGM10);
//No prescaling therefore timer frequency = 8 MHz and PWM frequency = 31250 Hz
TCCR1B|=(1<<WGM12)|(1<<CS10);
TCNT1=0x00;
OCR1A=BASE_LEVEL;
//Enable the timer interrupt
TIMSK1 |= ( 1 <<TOIE1);
//Clear all interupt flags
TIFR1|=(1<<ICF1)|(1<<OCF1B)|(1<<OCF1A)|(1<<TOV1);
//Enable interrupts
sei();
}
int main(void)
{
//PB1 is OC1A. Use this for output
DDRB |= (1 << PB1);
pwm_init();
/* insert your hardware initialization here */
for(;;){
/* insert your main loop code here */
}
return 0; /* never reached */
}
Switch.h (Sound file)
const unsigned char switch_raw PROGMEM = {
0x52, 0x49, 0x46, 0x46, 0x0d, 0x04, 0x00, 0x00, 0x57, 0x41, 0x56, 0x45,
0x66, 0x6d, 0x74, 0x20, 0x10, 0x00, 0x00, 0x00, 0x01, 0x00, 0x01, 0x00,
0x09, 0x3d, 0x00, 0x00, 0x09, 0x3d, 0x00, 0x00, 0x01, 0x00, 0x08, 0x00,
0x64, 0x61, 0x74, 0x61, 0x4b, 0x03, 0x00, 0x00, 0x80, 0x7f, 0x7f, 0x7e,
0x7f, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7f, 0x80, 0x7f, 0x7e, 0x7e,
0x7f, 0x80, 0x7f, 0x7f, 0x7e, 0x7d, 0x7f, 0x81, 0x7e, 0x7e, 0x7f, 0x7f,
0x7e, 0x7e, 0x7f, 0x7f, 0x7f, 0x7d, 0x80, 0x81, 0x7e, 0x7b, 0x7e, 0x7f,
0x7f, 0x81, 0x7e, 0x7e, 0x7d, 0x80, 0x80, 0x7e, 0x7e, 0x7e, 0x7d, 0x7e,
0x80, 0x80, 0x7e, 0x7c, 0x7d, 0x7f, 0x81, 0x7f, 0x7e, 0x81, 0x7d, 0x7b,
0x80, 0x7f, 0x7f, 0x83, 0x7f, 0x7b, 0x7f, 0x80, 0x7f, 0x82, 0x7f, 0x7e,
0x80, 0x7e, 0x81, 0x7f, 0x7f, 0x81, 0x7d, 0x7e, 0x80, 0x7e, 0x80, 0x7e,
0x7f, 0x85, 0x80, 0x83, 0x7b, 0x77, 0x83, 0x81, 0x86, 0x7e, 0x7b, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x7f, 0x81, 0x82, 0x7f, 0x7e, 0x7e, 0x7e,
0x81, 0x83, 0x7f, 0x7f, 0x7f, 0x80, 0x80, 0x81, 0x7e, 0x7e, 0x80, 0x83,
0x7f, 0x7d, 0x7b, 0x80, 0x80, 0x94, 0x79, 0x68, 0x87, 0x75, 0x98, 0x87,
0x6e, 0x7f, 0x8c, 0x81, 0x54, 0x7c, 0xc4, 0x8a, 0x46, 0x31, 0x72, 0xe2,
0xc1, 0x8a, 0x41, 0x2f, 0x71, 0xb3, 0xc8, 0x96, 0x51, 0x41, 0x67, 0x9c,
0xb1, 0x98, 0x74, 0x57, 0x5f, 0x76, 0x99, 0xa8, 0x96, 0x72, 0x5b, 0x64,
0x7e, 0x97, 0xa1, 0x8f, 0x6f, 0x56, 0x66, 0x89, 0xa0, 0x9d, 0x7e, 0x62,
0x5c, 0x78, 0x93, 0x9d, 0x90, 0x70, 0x58, 0x68, 0x88, 0x9c, 0x95, 0x7c,
0x66, 0x64, 0x7c, 0x90, 0x95, 0x82, 0x6f, 0x6b, 0x75, 0x86, 0x8e, 0x88,
0x79, 0x72, 0x75, 0x80, 0x88, 0x89, 0x81, 0x78, 0x74, 0x78, 0x84, 0x85,
0x84, 0x7d, 0x7b, 0x7c, 0x7b, 0x80, 0x85, 0x87, 0x81, 0x76, 0x74, 0x7e,
0x82, 0x89, 0x84, 0x7c, 0x77, 0x78, 0x84, 0x83, 0x84, 0x7c, 0x78, 0x7b,
0x83, 0x83, 0x80, 0x83, 0x80, 0x7d, 0x7a, 0x7e, 0x83, 0x87, 0x82, 0x79,
0x78, 0x7e, 0x87, 0x8b, 0x80, 0x76, 0x79, 0x7e, 0x87, 0x87, 0x80, 0x7a,
0x7a, 0x80, 0x82, 0x84, 0x81, 0x7f, 0x7e, 0x7d, 0x7a, 0x82, 0x88, 0x7f,
0x7a, 0x79, 0x7f, 0x85, 0x85, 0x7f, 0x7d, 0x7a, 0x7d, 0x83, 0x87, 0x7e,
0x78, 0x7e, 0x7d, 0x83, 0x7e, 0x81, 0x81, 0x80, 0x7f, 0x81, 0x81, 0x7c,
0x7e, 0x7a, 0x81, 0x82, 0x81, 0x84, 0x82, 0x79, 0x78, 0x84, 0x86, 0x7d,
0x7b, 0x7e, 0x7f, 0x7c, 0x7d, 0x7d, 0x82, 0x80, 0x80, 0x7e, 0x7d, 0x85,
0x84, 0x7b, 0x75, 0x7c, 0x7d, 0x84, 0x88, 0x84, 0x7b, 0x7b, 0x7d, 0x7c,
0x88, 0x88, 0x7b, 0x78, 0x78, 0x78, 0x88, 0x8d, 0x80, 0x78, 0x7f, 0x86,
0x86, 0x83, 0x7c, 0x71, 0x76, 0x84, 0x97, 0x93, 0x70, 0x6d, 0x68, 0x78,
0xc5, 0xb6, 0x5f, 0x37, 0x2a, 0x69, 0xc1, 0xc9, 0xa0, 0x7a, 0x52, 0x50,
0x71, 0x8a, 0x9d, 0xa0, 0x8b, 0x69, 0x67, 0x68, 0x79, 0x94, 0x96, 0x87,
0x7b, 0x81, 0x84, 0x7e, 0x7d, 0x7e, 0x75, 0x72, 0x89, 0x8e, 0x88, 0x86,
0x6d, 0x6d, 0x7a, 0x82, 0x8d, 0x8e, 0x78, 0x76, 0x7f, 0x7d, 0x7e, 0x82,
0x80, 0x7b, 0x7d, 0x7a, 0x7b, 0x86, 0x89, 0x80, 0x7b, 0x75, 0x77, 0x7f,
0x83, 0x84, 0x86, 0x81, 0x81, 0x7e, 0x73, 0x7c, 0x83, 0x7f, 0x85, 0x82,
0x7d, 0x83, 0x7d, 0x7d, 0x80, 0x7b, 0x7c, 0x86, 0x85, 0x7e, 0x7b, 0x74,
0x7d, 0x86, 0x85, 0x8b, 0x81, 0x76, 0x78, 0x78, 0x7e, 0x89, 0x83, 0x7e,
0x80, 0x78, 0x7f, 0x84, 0x81, 0x84, 0x7a, 0x77, 0x7f, 0x81, 0x84, 0x81,
0x78, 0x7a, 0x7e, 0x84, 0x8e, 0x81, 0x72, 0x75, 0x77, 0x83, 0x8b, 0x84,
0x84, 0x7b, 0x72, 0x7a, 0x83, 0x84, 0x85, 0x7e, 0x78, 0x7e, 0x7d, 0x7f,
0x82, 0x80, 0x7f, 0x7e, 0x7f, 0x81, 0x7e, 0x7b, 0x80, 0x85, 0x84, 0x82,
0x7d, 0x7a, 0x7d, 0x7f, 0x84, 0x84, 0x7f, 0x79, 0x7b, 0x82, 0x80, 0x80,
0x81, 0x80, 0x81, 0x81, 0x7f, 0x7e, 0x79, 0x79, 0x81, 0x86, 0x85, 0x82,
0x7d, 0x77, 0x7a, 0x7e, 0x86, 0x8b, 0x84, 0x7a, 0x7a, 0x7d, 0x7e, 0x83,
0x83, 0x80, 0x7e, 0x7c, 0x7c, 0x80, 0x7f, 0x80, 0x7f, 0x7f, 0x80, 0x7e,
0x7f, 0x80, 0x7f, 0x7c, 0x80, 0x7d, 0x7e, 0x85, 0x81, 0x7c, 0x7d, 0x7b,
0x7c, 0x81, 0x80, 0x7d, 0x7f, 0x80, 0x7d, 0x82, 0x84, 0x7e, 0x7a, 0x7e,
0x7e, 0x7f, 0x82, 0x7d, 0x7e, 0x81, 0x7f, 0x7d, 0x7e, 0x81, 0x83, 0x83,
0x80, 0x79, 0x77, 0x7c, 0x83, 0x87, 0x86, 0x7f, 0x75, 0x79, 0x7e, 0x85,
0x86, 0x80, 0x7a, 0x78, 0x7c, 0x7f, 0x83, 0x81, 0x82, 0x7d, 0x7a, 0x7f,
0x81, 0x80, 0x80, 0x7c, 0x7b, 0x80, 0x7e, 0x80, 0x85, 0x84, 0x7d, 0x7b,
0x7a, 0x7f, 0x83, 0x82, 0x80, 0x7c, 0x7e, 0x7e, 0x80, 0x81, 0x7f, 0x7f,
0x7e, 0x7f, 0x82, 0x7f, 0x7c, 0x7b, 0x7b, 0x82, 0x84, 0x83, 0x7e, 0x7c,
0x7b, 0x7e, 0x83, 0x81, 0x7f, 0x7d, 0x7e, 0x7f, 0x83, 0x81, 0x7e, 0x7d,
0x7b, 0x7d, 0x80, 0x82, 0x81, 0x80, 0x7f, 0x7d, 0x7f, 0x80, 0x7f, 0x80,
0x81, 0x80, 0x7f, 0x7d, 0x7d, 0x7e, 0x81, 0x82, 0x80, 0x7d, 0x7f, 0x81,
0x80, 0x7f, 0x7d, 0x7c, 0x7e, 0x80, 0x80, 0x80, 0x80, 0x80, 0x7e, 0x7f,
0x7d, 0x7e, 0x80, 0x81, 0x80, 0x7f, 0x7e, 0x7c, 0x7f, 0x81, 0x80, 0x80,
0x80, 0x7f, 0x7e, 0x7e, 0x7f, 0x7f, 0x80, 0x80, 0x80, 0x81, 0x80, 0x7d,
0x7c, 0x7f, 0x80, 0x83, 0x81, 0x7c, 0x7b, 0x7c, 0x7f, 0x82, 0x82, 0x7f,
0x7d, 0x7c, 0x7e, 0x80, 0x81, 0x81, 0x7f, 0x7f, 0x7d, 0x7d, 0x80, 0x82,
0x7f, 0x7e, 0x7d, 0x7d, 0x80, 0x83, 0x82, 0x7f, 0x7f, 0x7a, 0x7d, 0x80,
0x81, 0x81, 0x80, 0x7e, 0x7f, 0x80, 0x7e, 0x7e, 0x7f, 0x80, 0x7f, 0x80,
0x7f, 0x7e, 0x7d, 0x7f, 0x7e, 0x80, 0x81, 0x81, 0x80, 0x80, 0x7e, 0x7e,
0x7e, 0x7d, 0x80, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7e, 0x7c, 0x7f, 0x82,
0x7f, 0x80, 0x7f, 0x7d, 0x7d, 0x7f, 0x7f, 0x80, 0x80, 0x7f, 0x7e, 0x7f,
0x7f, 0x7f, 0x80, 0x7e, 0x7f, 0x7f, 0x80, 0x81, 0x7f, 0x7e, 0x7d, 0x7d,
0x81, 0x82, 0x80, 0x7e, 0x7d, 0x7e, 0x80, 0x81, 0x7f, 0x80, 0x80, 0x7f,
0x7f, 0x7d, 0x7f, 0x81, 0x80, 0x7f, 0x80, 0x7f, 0x7e, 0x7d, 0x7e, 0x4c,
0x49, 0x53, 0x54, 0x48, 0x00, 0x00, 0x00, 0x49, 0x4e, 0x46, 0x4f, 0x49,
0x43, 0x52, 0x44, 0x12, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31, 0x36, 0x2d,
0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32, 0x37, 0x00,
0x00, 0x49, 0x53, 0x46, 0x54, 0x22, 0x00, 0x00, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x20, 0x28,
0x6c, 0x69, 0x62, 0x73, 0x6e, 0x64, 0x66, 0x69, 0x6c, 0x65, 0x2d, 0x31,
0x2e, 0x30, 0x2e, 0x32, 0x34, 0x29, 0x00, 0x69, 0x64, 0x33, 0x20, 0x46,
0x00, 0x00, 0x00, 0x49, 0x44, 0x33, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00,
0x3c, 0x54, 0x58, 0x58, 0x58, 0x00, 0x00, 0x00, 0x17, 0x00, 0x00, 0x00,
0x53, 0x6f, 0x66, 0x74, 0x77, 0x61, 0x72, 0x65, 0x00, 0x4c, 0x61, 0x76,
0x66, 0x35, 0x37, 0x2e, 0x37, 0x32, 0x2e, 0x31, 0x30, 0x31, 0x54, 0x44,
0x52, 0x43, 0x00, 0x00, 0x00, 0x11, 0x00, 0x00, 0x00, 0x32, 0x30, 0x31,
0x36, 0x2d, 0x31, 0x30, 0x2d, 0x31, 0x37, 0x20, 0x31, 0x37, 0x3a, 0x32,
0x37
};
const long switchResampled_len = 1045;
audio pwm atmega
audio pwm atmega
asked 4 hours ago
cheunste
584
asked 4 hours ago
cheunste
584
asked 4 hours ago
cheunste
584
asked 4 hours ago
cheunste
584
asked 4 hours ago
cheunste
584
584
That is likely the fundamental PWM rate, wherein you are modifying the DUTY CYCLE but not the repetition rate.
– analogsystemsrf
4 hours ago
1045 samples at 15.625kHz is only 67mSec worth of data. How are you hearing anything in only 67mSec?
– brhans
4 hours ago
add a comment |
That is likely the fundamental PWM rate, wherein you are modifying the DUTY CYCLE but not the repetition rate.
– analogsystemsrf
4 hours ago
1045 samples at 15.625kHz is only 67mSec worth of data. How are you hearing anything in only 67mSec?
– brhans
4 hours ago
That is likely the fundamental PWM rate, wherein you are modifying the DUTY CYCLE but not the repetition rate.
– analogsystemsrf
4 hours ago
That is likely the fundamental PWM rate, wherein you are modifying the DUTY CYCLE but not the repetition rate.
– analogsystemsrf
4 hours ago
1045 samples at 15.625kHz is only 67mSec worth of data. How are you hearing anything in only 67mSec?
– brhans
4 hours ago
1045 samples at 15.625kHz is only 67mSec worth of data. How are you hearing anything in only 67mSec?
– brhans
4 hours ago
add a comment |
1 Answer
1
active
oldest
votes
4
A 4MHz PWM generator (8MHz/2) At 8 bits has a 15.625kHz fundamental. If you are not filtering this out with at least a 7kHz high-order low-pass you will hear it loud and clear.
You need to bring this fundamental to at least above 20kHz or so to get it out of your hearing range, it will still annoy your dog though.
answered 3 hours ago
Edgar Brown
3,143425
Or maybe he could use a notch filter.
– Harry Svensson
2 hours ago
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f413276%2ftrying-a-pwm-audio-application-i-cant-figure-out-why-im-getting-a-loud-beep-o%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
4
A 4MHz PWM generator (8MHz/2) At 8 bits has a 15.625kHz fundamental. If you are not filtering this out with at least a 7kHz high-order low-pass you will hear it loud and clear.
You need to bring this fundamental to at least above 20kHz or so to get it out of your hearing range, it will still annoy your dog though.
answered 3 hours ago
Edgar Brown
3,143425
Or maybe he could use a notch filter.
– Harry Svensson
2 hours ago
add a comment |
4
A 4MHz PWM generator (8MHz/2) At 8 bits has a 15.625kHz fundamental. If you are not filtering this out with at least a 7kHz high-order low-pass you will hear it loud and clear.
You need to bring this fundamental to at least above 20kHz or so to get it out of your hearing range, it will still annoy your dog though.
answered 3 hours ago
Edgar Brown
3,143425
Or maybe he could use a notch filter.
– Harry Svensson
2 hours ago
add a comment |
4
4
4
A 4MHz PWM generator (8MHz/2) At 8 bits has a 15.625kHz fundamental. If you are not filtering this out with at least a 7kHz high-order low-pass you will hear it loud and clear.
You need to bring this fundamental to at least above 20kHz or so to get it out of your hearing range, it will still annoy your dog though.
answered 3 hours ago
Edgar Brown
3,143425
A 4MHz PWM generator (8MHz/2) At 8 bits has a 15.625kHz fundamental. If you are not filtering this out with at least a 7kHz high-order low-pass you will hear it loud and clear.
You need to bring this fundamental to at least above 20kHz or so to get it out of your hearing range, it will still annoy your dog though.
answered 3 hours ago
Edgar Brown
3,143425
answered 3 hours ago
Edgar Brown
3,143425
answered 3 hours ago
Edgar Brown
3,143425
answered 3 hours ago
Edgar Brown
3,143425
3,143425
Or maybe he could use a notch filter.
– Harry Svensson
2 hours ago
add a comment |
Or maybe he could use a notch filter.
– Harry Svensson
2 hours ago
Or maybe he could use a notch filter.
– Harry Svensson
2 hours ago
Or maybe he could use a notch filter.
– Harry Svensson
2 hours ago
add a comment |
draft saved
draft discarded
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f413276%2ftrying-a-pwm-audio-application-i-cant-figure-out-why-im-getting-a-loud-beep-o%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
That is likely the fundamental PWM rate, wherein you are modifying the DUTY CYCLE but not the repetition rate.
– analogsystemsrf
4 hours ago
1045 samples at 15.625kHz is only 67mSec worth of data. How are you hearing anything in only 67mSec?
– brhans
4 hours ago