Continuity on hot/neutral at dead outlet





.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty{ margin-bottom:0;
}






up vote
1
down vote

favorite












I have an outlet that has stopped working.
When it used to work I previously labeled which circuit it was on at the breaker. I'm rather certain I know which breaker supplies it. It also supplies other lights, which continue to work.



Turned off breaker, removed outlet from wall and disconnected from wires. Powered on breaker, and confirm with multimeter no AC measured on bare wires at outlet. (Proving that this is not a faulty outlet.)



Have a continuity tester (part of a tone generator). I am getting continuity across hot and neutral on these wires.
(Edit: also getting continuity between neutral and ground wire, as well. 20 ohms hot/neutral, 1 ohm neutral/ground, 20 ohms hot/ground. WTF??) What does this imply? How could I have done this?



I'm still trying to use the tone generator to trace where the wires feeding this outlet come from, but the continuity is making the signal very weak.






electrical







share|improve this question




















  • 3




    1 ohm neutral <---> ground is normal; 20 ohms Hot <--> neutral & ground sounds like you are detecting some other device in the circuit.
    – manassehkatz
    4 hours ago






  • 1




    Is there anything plugged into the circuit? Unscrew all the lightbulbs on it and unplug everything attached to receptacles on it, and see if you still get continuity
    – ThreePhaseEel
    2 hours ago






  • 1




    Thanks @manassehkatz for encouraging me to disconnect everything else until I found the problem (see my answer).
    – Phrogz
    1 hour ago






  • 1




    Thanks, too, to @ThreePhaseEel.
    – Phrogz
    1 hour ago

















up vote
1
down vote

favorite












I have an outlet that has stopped working.
When it used to work I previously labeled which circuit it was on at the breaker. I'm rather certain I know which breaker supplies it. It also supplies other lights, which continue to work.



Turned off breaker, removed outlet from wall and disconnected from wires. Powered on breaker, and confirm with multimeter no AC measured on bare wires at outlet. (Proving that this is not a faulty outlet.)



Have a continuity tester (part of a tone generator). I am getting continuity across hot and neutral on these wires.
(Edit: also getting continuity between neutral and ground wire, as well. 20 ohms hot/neutral, 1 ohm neutral/ground, 20 ohms hot/ground. WTF??) What does this imply? How could I have done this?



I'm still trying to use the tone generator to trace where the wires feeding this outlet come from, but the continuity is making the signal very weak.






electrical







share|improve this question




















  • 3




    1 ohm neutral <---> ground is normal; 20 ohms Hot <--> neutral & ground sounds like you are detecting some other device in the circuit.
    – manassehkatz
    4 hours ago






  • 1




    Is there anything plugged into the circuit? Unscrew all the lightbulbs on it and unplug everything attached to receptacles on it, and see if you still get continuity
    – ThreePhaseEel
    2 hours ago






  • 1




    Thanks @manassehkatz for encouraging me to disconnect everything else until I found the problem (see my answer).
    – Phrogz
    1 hour ago






  • 1




    Thanks, too, to @ThreePhaseEel.
    – Phrogz
    1 hour ago













up vote
1
down vote

favorite









up vote
1
down vote

favorite











I have an outlet that has stopped working.
When it used to work I previously labeled which circuit it was on at the breaker. I'm rather certain I know which breaker supplies it. It also supplies other lights, which continue to work.



Turned off breaker, removed outlet from wall and disconnected from wires. Powered on breaker, and confirm with multimeter no AC measured on bare wires at outlet. (Proving that this is not a faulty outlet.)



Have a continuity tester (part of a tone generator). I am getting continuity across hot and neutral on these wires.
(Edit: also getting continuity between neutral and ground wire, as well. 20 ohms hot/neutral, 1 ohm neutral/ground, 20 ohms hot/ground. WTF??) What does this imply? How could I have done this?



I'm still trying to use the tone generator to trace where the wires feeding this outlet come from, but the continuity is making the signal very weak.






electrical







share|improve this question















I have an outlet that has stopped working.
When it used to work I previously labeled which circuit it was on at the breaker. I'm rather certain I know which breaker supplies it. It also supplies other lights, which continue to work.



Turned off breaker, removed outlet from wall and disconnected from wires. Powered on breaker, and confirm with multimeter no AC measured on bare wires at outlet. (Proving that this is not a faulty outlet.)



Have a continuity tester (part of a tone generator). I am getting continuity across hot and neutral on these wires.
(Edit: also getting continuity between neutral and ground wire, as well. 20 ohms hot/neutral, 1 ohm neutral/ground, 20 ohms hot/ground. WTF??) What does this imply? How could I have done this?



I'm still trying to use the tone generator to trace where the wires feeding this outlet come from, but the continuity is making the signal very weak.






electrical




electrical






share|improve this question















share|improve this question













share|improve this question




share|improve this question








edited 4 hours ago

























asked 5 hours ago









Phrogz

3831620




3831620








  • 3




    1 ohm neutral <---> ground is normal; 20 ohms Hot <--> neutral & ground sounds like you are detecting some other device in the circuit.
    – manassehkatz
    4 hours ago






  • 1




    Is there anything plugged into the circuit? Unscrew all the lightbulbs on it and unplug everything attached to receptacles on it, and see if you still get continuity
    – ThreePhaseEel
    2 hours ago






  • 1




    Thanks @manassehkatz for encouraging me to disconnect everything else until I found the problem (see my answer).
    – Phrogz
    1 hour ago






  • 1




    Thanks, too, to @ThreePhaseEel.
    – Phrogz
    1 hour ago














  • 3




    1 ohm neutral <---> ground is normal; 20 ohms Hot <--> neutral & ground sounds like you are detecting some other device in the circuit.
    – manassehkatz
    4 hours ago






  • 1




    Is there anything plugged into the circuit? Unscrew all the lightbulbs on it and unplug everything attached to receptacles on it, and see if you still get continuity
    – ThreePhaseEel
    2 hours ago






  • 1




    Thanks @manassehkatz for encouraging me to disconnect everything else until I found the problem (see my answer).
    – Phrogz
    1 hour ago






  • 1




    Thanks, too, to @ThreePhaseEel.
    – Phrogz
    1 hour ago








3




3




1 ohm neutral <---> ground is normal; 20 ohms Hot <--> neutral & ground sounds like you are detecting some other device in the circuit.
– manassehkatz
4 hours ago




1 ohm neutral <---> ground is normal; 20 ohms Hot <--> neutral & ground sounds like you are detecting some other device in the circuit.
– manassehkatz
4 hours ago




1




1




Is there anything plugged into the circuit? Unscrew all the lightbulbs on it and unplug everything attached to receptacles on it, and see if you still get continuity
– ThreePhaseEel
2 hours ago




Is there anything plugged into the circuit? Unscrew all the lightbulbs on it and unplug everything attached to receptacles on it, and see if you still get continuity
– ThreePhaseEel
2 hours ago




1




1




Thanks @manassehkatz for encouraging me to disconnect everything else until I found the problem (see my answer).
– Phrogz
1 hour ago




Thanks @manassehkatz for encouraging me to disconnect everything else until I found the problem (see my answer).
– Phrogz
1 hour ago




1




1




Thanks, too, to @ThreePhaseEel.
– Phrogz
1 hour ago




Thanks, too, to @ThreePhaseEel.
– Phrogz
1 hour ago










1 Answer
1






active

oldest

votes

















up vote
2
down vote













Thanks to @manassehkatz I went to all light switches on the same circuit and disconnected them. The outlet retained continuity.



I then traced the wire through the crawlspace to a wall with another light switch that I did not realize was on the same circuit. Opening that box and removing the switches I found that the line to the outlet comes from that box, and I somehow failed to reconnect power to the outlet when I was changing out my dimmer switches. The neutral was connected, but the hot line to the outlet was just loose in the back of the box. (Yikes.)



I'm not sure what connection it was making when everything was crammed into the box. I'm guessing it was loosely connecting to one of the free ground wires. Once I removed the switches from the box continuity disappeared. And, once I connected the wires properly, the outlet works again.






share|improve this answer





















    Your Answer








    StackExchange.ready(function() {
    var channelOptions = {
    tags: "".split(" "),
    id: "73"
    };
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function() {
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled) {
    StackExchange.using("snippets", function() {
    createEditor();
    });
    }
    else {
    createEditor();
    }
    });

    function createEditor() {
    StackExchange.prepareEditor({
    heartbeatType: 'answer',
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader: {
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    },
    noCode: true, onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    });


    }
    });














     

    draft saved


    draft discarded


















    StackExchange.ready(
    function () {
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f151287%2fcontinuity-on-hot-neutral-at-dead-outlet%23new-answer', 'question_page');
    }
    );

    Post as a guest















    Required, but never shown

























    1 Answer
    1






    active

    oldest

    votes








    1 Answer
    1






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes








    up vote
    2
    down vote













    Thanks to @manassehkatz I went to all light switches on the same circuit and disconnected them. The outlet retained continuity.



    I then traced the wire through the crawlspace to a wall with another light switch that I did not realize was on the same circuit. Opening that box and removing the switches I found that the line to the outlet comes from that box, and I somehow failed to reconnect power to the outlet when I was changing out my dimmer switches. The neutral was connected, but the hot line to the outlet was just loose in the back of the box. (Yikes.)



    I'm not sure what connection it was making when everything was crammed into the box. I'm guessing it was loosely connecting to one of the free ground wires. Once I removed the switches from the box continuity disappeared. And, once I connected the wires properly, the outlet works again.






    share|improve this answer

























      up vote
      2
      down vote













      Thanks to @manassehkatz I went to all light switches on the same circuit and disconnected them. The outlet retained continuity.



      I then traced the wire through the crawlspace to a wall with another light switch that I did not realize was on the same circuit. Opening that box and removing the switches I found that the line to the outlet comes from that box, and I somehow failed to reconnect power to the outlet when I was changing out my dimmer switches. The neutral was connected, but the hot line to the outlet was just loose in the back of the box. (Yikes.)



      I'm not sure what connection it was making when everything was crammed into the box. I'm guessing it was loosely connecting to one of the free ground wires. Once I removed the switches from the box continuity disappeared. And, once I connected the wires properly, the outlet works again.






      share|improve this answer























        up vote
        2
        down vote










        up vote
        2
        down vote









        Thanks to @manassehkatz I went to all light switches on the same circuit and disconnected them. The outlet retained continuity.



        I then traced the wire through the crawlspace to a wall with another light switch that I did not realize was on the same circuit. Opening that box and removing the switches I found that the line to the outlet comes from that box, and I somehow failed to reconnect power to the outlet when I was changing out my dimmer switches. The neutral was connected, but the hot line to the outlet was just loose in the back of the box. (Yikes.)



        I'm not sure what connection it was making when everything was crammed into the box. I'm guessing it was loosely connecting to one of the free ground wires. Once I removed the switches from the box continuity disappeared. And, once I connected the wires properly, the outlet works again.






        share|improve this answer












        Thanks to @manassehkatz I went to all light switches on the same circuit and disconnected them. The outlet retained continuity.



        I then traced the wire through the crawlspace to a wall with another light switch that I did not realize was on the same circuit. Opening that box and removing the switches I found that the line to the outlet comes from that box, and I somehow failed to reconnect power to the outlet when I was changing out my dimmer switches. The neutral was connected, but the hot line to the outlet was just loose in the back of the box. (Yikes.)



        I'm not sure what connection it was making when everything was crammed into the box. I'm guessing it was loosely connecting to one of the free ground wires. Once I removed the switches from the box continuity disappeared. And, once I connected the wires properly, the outlet works again.







        share|improve this answer












        share|improve this answer



        share|improve this answer










        answered 1 hour ago









        Phrogz

        3831620




        3831620






























             

            draft saved


            draft discarded



















































             


            draft saved


            draft discarded














            StackExchange.ready(
            function () {
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f151287%2fcontinuity-on-hot-neutral-at-dead-outlet%23new-answer', 'question_page');
            }
            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            -

            Popular posts from this blog

            Bundesstraße 106

            Image
            Dieser Artikel beschreibt die Bundesstraße 106 in Deutschland. Zur gleichnamigen Straße in Österreich siehe Mölltal Straße. Vorlage:Infobox hochrangige Straße/Wartung/DE-B Bundesstraße 106 in Deutschland Karte Basisdaten Betreiber: Deutschland  Bundesrepublik Deutschland Straßenbeginn: Wismar ( 53° 54′  N , 11° 24′  O 53.900536 11.396875 ) Straßenende: Schwerin ( 53° 36′  N , 11° 24′  O 53.592785 11.404892 ) Gesamtlänge: 40,7 km Bundesland: Mecklenburg-Vorpommern Ausbauzustand: zweistreifig [1] Bundesstraße 106 in Schwerin (Umgehungsstraße) Straßenverlauf Land Mecklenburg-Vorpommern Landkreis Nordwestmecklenburg Ortsumgehung Wismar Wallensteingraben über   Dorf Mecklenburg Wallensteingraben Groß Stieten Bad Kleinen OT Niendorf Bahnstrecke Lübeck–Bad Kleinen Zickhusen Lübstorf Klein Trebbow OT Kirch Stück
            Read more

            Verónica Boquete

            Image
            Verónica Boquete im Trikot der Nationalmannschaft (2013) Personalia Name Verónica Boquete Giadans Geburtstag 9. April 1987 Geburtsort Santiago de Compostela, Spanien Größe 159 cm Position Mittelfeld / Sturm Juniorinnen Jahre Station 2001–2005 Xuventú Aguiño Frauen Jahre Station Spiele (Tore) 1 2005–2008 Prainsa Zaragoza 83 (40) 2008–2010 Espanyol Barcelona 53 (30) 2010 Buffalo Flash 9 0 (9) 2010 Chicago Red Stars 3 0 (1) 2010–2011 Espanyol Barcelona 26 (41) 2011 Philadelphia Independence 13 0 (5) 2011 Energija Woronesch 5 0 (1) 2012–2014 Tyresö FF 39 (14) 2014 Portland Thorns FC 15 0 (4) 2014–2015 1. FFC Frankfurt 23 0 (7) 2015–2016 FC Bayern München 9 0 (0) 2016–2018 Paris Saint-Germain 31 0 (8) 2018 Peking BG Phoenix 2019– Utah Royals FC 0 0 (0) Nationalmannschaft Jahre Auswahl
            Read more

            Ida-Boy-Ed-Garten

            Image
            Die Lage des Ida-Boy-Ed-Gartens, rot markiert Der Ida-Boy-Ed-Garten Der Ida-Boy-Ed-Garten, Blick von der Wakenitzmauer durch das Tor in der Stadtmauer Der Ida-Boy-Ed-Garten ist eine Straße der Lübecker Altstadt. Inhaltsverzeichnis 1 Lage 2 Geschichte 3 Literatur 4 Weblinks Lage | Der etwa 90 Meter lange Ida-Boy-Ed-Garten befindet sich an der nördlichen Spitze der Altstadtinsel, vor dem Burgtor. Die in einem Bogen durch eine Grünanlage hangaufwärts führende Straße verbindet die Wakenitzmauer mit der Burgtorbrücke. Geschichte | Der heutige Ida-Boy-Ed-Garten wurde ursprünglich als Verlängerung der Wakenitzmauer angelegt. 1903 wurde in den erhaltenen Teil der mittelalterlichen Stadtmauer, an dem die Wakenitzmauer bei der Einmündung der Kaiserstraße begann, ein Tor mit einem großen Bogen für die Durchführung der Straße und zwei kleineren seitlichen Öffnungen für Fußgänger gebrochen, um für die neu errichteten Wohnhäuser in diesem Bereich
            Read more